4G-IoT方案_03

IoT solar street light is a more intelligent road lighting product combined with IoT technology. It can calculate the power generation in real time through IoT and tell us how much carbon emission has been reduced. At the same time, it can monitor the operation status of the solar street light in real time through IoT, and put a real-time alarm to the faults, which can greatly improve the maintenance efficiency of the solar street light.

National Standard Lux Of Led Street Light

4G-IoT方案_07

Lights Arrangement Types Of Smart Solar Street Light Recommend TYPE-B / C / D

Highway-Solar-Lights_06

One-sided lighting

Highway-Solar-Lights_08

Double-sided "Z"-shaped lighting

Highway-Solar-Lights_10

Symmetrical lighting on both sides

Highway-Solar-Lights_12

Symmetrical lighting in the center of the road

Brightness Of Highway Working Mode Options

Mode 1 : Work at full brightness all night.

Highway-Solar-Lights_74jpg_19
Highway-Solar-Lights_334_19
Highway-Solar-Lights_777_25

Mode 2 : Work at full bightness before midnight, work in dimming mode after midnight.

Highway-Solar-Lights_19
Highway-Solar-Lights_21
Highway-Solar-Lights_23

Mode 3 : Add a MOTION SENSOR, the light is 100% on when there is a car passing by, work in dimming mode when there is no car passing by.

Highway-Solar-Lights_29

From the perspective of cost, Model 1 > Model 2 > Model 3

Light Distributions Mode Of Smart Solar Street Light Recommend TYPE II & TYPE III

Light Distributions Model

TYPE I

 In the IESNA
Standard,  The Type I distribution is great for lighting walkways, 
paths and  sidewalks. It is generally applicable to where the 
mounting height is  approximately equal to the roadway width.

TYPE II

In the IESNA Standard,  the Type II distribution is used for wide walkways, on ramps and  entrance roadways, as well as other long, narrow lighting. It is generally  applicable to where the width of the roadway does not exceed 1.75 times the designed mounting
height.

TYPE III

In the IESNA Standard,  the Type III distribution is meant for roadway lighting, 
general parking  areas and other areas where a largerarea of lighting is required. This  distribution is intended for luminaires 
mounted at or near the side of  medium width roadways or areas, where the width of the roadway or area  does not exceed
2.75 times the mounting height.

TYPE V

The Type V lens of BOSUN solar  street light . In the IESNA  Standard,It is intended for luminaire mounting at or near center of  roadways,center islands of parkway, and intersections. It is also meant  for large, commercial parking lot lighting as well as areas where suticient,  evenly distributed light is necessary.

Recommended Models To Urban Road Solar Street Lights

All In One Solar Lights

All In One series is the most compact model. It integrates all components such as solar panel, lithium battery, solar controller and LED lighting source all together with the lighting fixture as one unit.

4G-IoT方案_11
4G-IoT方案_13
4G-IoT方案_15

Split-Type Solar Street Light

The whole system adopts split design, with completely separate design of solar panel, LED Lamp and Lithium Battery Unit. Lithium Battery units are usually mounted under panels or hung from light poles. Because the size of solar panel and Lithium Battery Unit can be large without limitation, it can support high-power LED lamp output to work for a long time, but the installation is more complicated than other models.

 

4G-IoT方案_19
4G-IoT方案_20
4G-IoT方案_21

PROJECT REFERENCE

CAsez-1_18
casez-2_09
casez-2_21
casez-2_03
casez-2_15
casezz-1_20
casez-2_06
casez-2_18
casez-2_27
casez-2_30

MORE SOLUTIONS

https://www.bosunsolar.com/highway-solar-lights/
Highway-Solar-Lights_67
ec5b4d38
Highway-Solar-Lights_60
Highway-Solar-Lights_69
700acbbe
Highway-Solar-Lights_62
Highway-Solar-Lights_71
Highway-Solar-Lights_64
Highway-Solar-Lights_73

Free Professional DIALux Lighting Design

Help You Win More Government & Commercial Project